Repairs & Modifications
-
I gave my cookie monter a good shave with this doodad I got from Wal-Mart for $7. It's hard to see but it looks a lot newer now. Worked good for shaving all the pils of the inside of the shirt. Be sure to use the gaurd because you will make holes in your shirt if you don't!
I am reluctant to suggest this because I don't want to be responsible if you put a hole in your UHF. I am going to try my oldest UHF next.
-
The result of shaving the front of the left sleeve. The fabric feels super smooth and soft again. This is my most favorite flannel shirt ever so I am going to be extra careful working on it.
-
I'm pleased to report that this worked great. Shocked at how well it worked actually. Only drawback is it burns through batteries pretty fast.
Before:
After:
-
Going for one final attempt to shrink the sleeve and leg openings of my 177 CPO and 888s. Boiling hot water.
-
does anyone have much experience overdying? i want to try it (on a shirt or two first, maybe a used pair) and have been searching for info best as i can… i know i am prob going to need a giant pot and maybe a gas burner if i want to boil outside... supposedly double the amount of rit dye recommended... soak before putting in, bring it to a simmer and agitate a bunch for about an hour?
anything better to use than rit dye (or is everything else more permanent w/ less fade potential)?
i know someone on here (in this thread?) did what looked like a nice OD job on a 14oz type III, but i can't find it right now.
-
I've had better luck with Tulip; I also prefer the liquid to the powder. But if you want it to fade, Rit is probably better. The reason I don't like it is that it isn't as colorfast.
When I dye stuff, I do it on the stove top, using a couple of burners to heat the water. I use a large metal tub, like this one. And yeah, at least double the dye that the instructions say.
-
@jvicente86:
Anyone have experience with getting the waist taken in on a pair of denim? I know railcar offers this service but not sure how much it will change the fit of the jeans.
Never done it, but I assume they take a dart out from where the side seam meets the waist band on each side, then re-fell the seams and sew. It would have to affect the fit of the top block to a degree…
-
What you guys think of this rough spot ? Do you think I should consider repair or leave it since it’s 25oz thick denim
Sent from my iPhone using Tapatalk
-
I'm usually an advocate for the "repair early, repair often" school of thought, but I wouldn't do anything to that spot.
-
https://de-de.facebook.com/MR-Handy-Denim-Repair-557460200965203/posts
Highly recommended for Denim repairs
-
@thomas01:
https://de-de.facebook.com/MR-Handy-Denim-Repair-557460200965203/posts
Highly recommended for Denim repairs
Thanks. I will keep that in mind.
-
Hello, old friend…
-
I didn't take any, but happily, Rain did-
https://www.instagram.com/p/BYtpwIuBo8P/There really wasn't much to be done; there was a hole by the right pocket, and another above the left knee, the hems were fraying a bit, and there were a couple of weak spots here and there. Naturally, she repaired more than I even realized needed it, because she's a damn master.
-
God she’s good. Can’t wait to see what @formulapfaff ‘s 55UHR look like when I see him at xmas - he was bummed they didn’t make it back to him before the meet up
Sent from my iPhone using Tapatalk
-
God she’s good. Can’t wait to see what @formulapfaff ‘s 55UHR look like when I see him at xmas - he was bummed they didn’t make it back to him before the meet up
Sent from my iPhone using Tapatalk
I didn't even know this thread existed…I'll post when they get here!
Sent from my Pixel 2 XL using Tapatalk
